How To Bolt Down The Safe To A Wooden Floor

How To Bolt Down The Safe To A Wooden Floor
How To Bolt Down The Safe To A Wooden Floor

We are reader-supported. When you buy through links on our site, we may earn an affiliate commission.

Buying a gun comes with an added responsibility of keeping it safe and nothing serves as a better option than a gun safe. As the name suggests, a gun safe keeps your weapon away from the reach of intruders. You can secure your weapon and keep it safe to further utilize it in the hours of need.

When it comes to protecting your gun safe, you have an array of options at your disposal. As gun safes are prone to theft in many circumstances, you cannot just keep them exposed or visible to others. Thus, an efficient way to keep both your weapon also a safe way from the reach of strangers is to bolt it down to the floor.

Reasons To Bolt Down A Safe To A Wooden Floor

bolting down the safe on the wooden floor
how to bolt down the safe to a wooden floor

Choosing the option of bolting down your safe to the floor increases the stability and security of your device. There is a multitude of options when it comes to choosing the area of bolting the safe and you must finalize the space after considering all the safety and security provisions in your home.

Your weapon should never lay around anywhere in your living space. Merely keeping your gun safe in your cupboard is not an option to secure your weapon. You need to find a guarded space that is out of the reach of a third-person or even your children in your home.

  • Bolting your safe to a wooden floor means increased security of your weapon against theft as no burglar would figure out the place where you have hidden the safe.
  • It also saves your gun from getting prone to external factors such as dust, corrosion, etc.

If you have a wooden floor, the below-listed tips and methods will give you an insight into how you can bolt the safe to it:

How To Bolt Down The Safe To A Wooden Floor?

dril on floor

First of all, you need to decide the particular location where you are planning to bolt the safe. This location should be low-key and must be away from the reach of the children or any intruder. Once you have zeroed on the location, the next step is to measure the area in which your safe will go. You need to cut out the space of the wood very properly so that the safe rests properly after which it shall be fixed and bolted using anchors and bolts.

The process of measurement is then followed by the rest of the instructions. You don’t have to make a heavy investment in the process of bolting the safe. All you are required to do is to assemble a few materials for an easy installation of the safe on the wooden floor. These materials include the basic drilling materials, such as a crowbar, saw, hammer drill, compressed air can, level, socket wrench, anchor kit with bolts, etc.

Bolting Down The Safe Using Crawlspace Method:

Different options of bolting down the safe to a wooden floor could be used to fulfill your purpose, however, the crawlspace is considered to be the safest option of all. To execute this method, you are required to drill the floor and make the use of huge nuts and washers to complete the process.

Alternatively, you can also use lag screws to fasten the gun safe and then secure the floor joist. If you are adopting the second option, make sure to check the space available under the floor. This can be done using a stud finder.

You can further use a wider steel sheet to bolt the safe in case the distance of the holes does not match the stud of the floors. After the completion of this step, you can mount the metal sheet to the floor studs. Experts further suggest using a concrete drill to bolt down the safe as this makes the entire process faster and easier.

The above-listed hand tools and equipment can be used to complete the process of bolting without any trouble. Lastly, do not forget to check the safe. If it appears to be loose, use a hammer and pins to pierce inside the floor and tighten the arrangement.

Bolting Down The Safe On A Raised Wooden Floor

If the wooden floor in your home is a little raised than normal, you will have to use a different method to bolt down your safe and secure it. It is essential to check the quality of the floorboard, especially if it measures 2×8 floor joists. You can use two different methods to secure your rifle safe on a raised wooden floor:

  1. To stabilize the safe on a raised wooden floor, drill the four lag bolts in the plywood. This helps to connect the mounting holes of the safe to the wood. Check for the position of the safe, it should not rock. If your safe still rocks, you can use a pry-bar under the safe to ward off it is rocking. Additionally, you can apply a strong adhesive to ensure that the safe is tightly gripped to the floor.
  2. Another safe option is to dig from within the safe via plywood flooring. Let the bolt come out from under the floor using a carriage bolt. Once done, you can secure the nut and washer from inside the safe. A carriage bolt cannot be removed from the front end which makes your safe remain secured, come what may. Check for the quality of the wooden crawlspace and make sure it belongs in a good condition so that you can carry out the process of bolting without any hassle.

Both these methods can easily help you attach the safe securely to the wooden floor. Before carrying out these methods, you need to ensure that the surface is clean and ready for operation. Always put the safe in the right position after drilling the wooden floor to avoid unwanted glitches.

Everything should be lined up evenly, without any hurdle or obstruction. Another important thing to check is the evenness of the floor. Basically, you are creating a shallow pit inside the wooden floor so that the safe could be preserved there securely.

Also if you are looking for other alternative ways to mount your gun safe then check out this post.

An uneven space might make the process of drilling and securing the safe difficult for you. Choose a spot that is even and safe. You can also use a level to test the evenness of the spot. Now that you have learned the method to bolt the gun safe to a wooden floor, it’s time to plan its execution.